| Trace
Heating
 |
Specification:-
Self regulating, fixed length, or site-cut zone parallel
heating tapes, as well as
ptfe or pvc insulated, or alloy sheathed heating cables.
Made in various power ratings, voltages,
& sheath materials, most can have stainless steel
overbraiding for mechanical protection, and/or
a polymer coating. Glassfibre insulated versions are available
for high temperature use, as well
as a full range of joiners, couplers, junction boxes,
thermostats, fixings, etc. EEx rated tapes, termination's,
& thermostats are also available.
Application:- Used for frost protection,
temperature maintenance, or process temperature
raising of pipework containing water, chemicals, fuel
oils, asphalt, tar, bitumen, wax, and other substances.
|
|
Flexible Mat Heaters
|
Specification:-
Consisting of resistance wire, tape, or pre-insulated
heating cable encapsulated
in layers of flexible insulating material. These mats,
jackets, blankets, & panels, can be used at temperatures
of up to 400 deg.C., and are available in a wide variety
of materials, such as silicon rubber, kapton, nomex, mylar,
quartz cloth, glass cloth, epoxy, aluminium foil, &
moulded GRP.
They can be self adhesive, strapped to the heated surface,
or held in place by integral eyelet's,
and can have built in thermostats or thermocouples. EEx
rated versions are available.
Application:- Used for temperature maintenance,
frost protection, and anti-condensation
heating of tanks & vessels, conical hoppers, vats,
and any irregularly shaped surfaces, in
industries such as petrochemicals, mining, pharmaceuticals,
medical technology, food processing, chemicals, and anywhere
that storage or transport of heat sensitive materials
is necessary. |
|
Infra-Red Emitters &
Assemblies
 |
Specification:-
Long, medium, & short wave infra-red emitters &
assemblies,using ceramic,
quartz tube, and metal sheathed elements in a variety
of styles & power ratings. Ceramic
emitters can have built in thermocouples if required.
Standard size reflectors and projectors are available,
as well as emitters for replacement into existing I/R
generators, while full panels & assemblies can be
built to cover almost any area, and to suit almost any
process application.
Application:- Used in personnel comfort
heating, animal husbandry, and many processes
involving non contact drying, curing, warming, thermoforming,
shrinking, cooking, & food
temperature maintenance. |
|
Drum Heaters
|
Specification:-
Metal clad or silicon rubber clamp-on types with built
in thermostat, to be used
singly, or in multiples. Made to suit standard drum sizes.
Rubber types are also made for use on
plastic drums & containers of various sizes. Also
full wrap around jacket types, with lid and
separate heated base, induction heated units for hazardous
areas, trolley type mobile units, and
direct immersion heaters, for insertion through the bung
hole. Non standard sizes made to order.
Hazardous area heater available for hire by week
or month.
Application:- Heating of various liquids
& chemicals in drums & containers, either for
safe
storage, or to achieve fluidity prior to pumping or processing. |
|
IBC Heaters
|
Specification:-
Base heater - Silicon rubber mat heater which can easily
be dropped into & removed from the
IBC cage. It has a built in PTC temperature sensor, and
comes with electronic temperature
controller and RCD.
Jacket - Made from water resistant, flame retardant insulated
polyurethane, with two separate
heating circuits and thermostats. Also available as an
insulation jacket only. The lid is not heated.
Application:- Heating of substances contained
in 1000 litre intermediate bulk containers. The
base heater’s sensitive control make sit suitable
for both high energy absorbing products, and
high viscosity, temperature sensitive materials.The insulation
jacket and lid will increase heat
up time, while combining the heated jacket with the base
heater will give maximum heating
capacity. |
|
Heating & Insulation
Jackets
|
Specification:-
Made from various high temperature resistant materials,
such as aluminised
glass cloth, PTFE coated glass fabric, woven glass cloth,
etc. with needle mat insulation of
fibreglass, Superwool™, etc. Stitched into literally
any shape using high temperature thread.
Capable of withstanding temperatures of up to 600°C.
depending on materials used. Available
with built in heating circuits to raise or maintain process
temperatures, and/or with built in
forced air cooling circuits. Various forms of attachment
are used, such as hooks and lacing, ties, velcro™
, grommets, straps, banding, etc.
Application:- Used in many industrial
applications, such as process temperature maintenance,
vacuum bakeout, mould preheating, extruder line barrel
insulation, pump and valve freeze
protection, antenna freeze protection, viscosity control,
composite processing, etc. |
|
|
|
|
